ATMF-CES DEFINITIONS::=BEGIN
IMPORTSenterprises FROM RFC1155-SMI
OBJECT-TYPE,MODULE-IDENTITY,Counter32,Gauge32FROM SNMPv2-SMI
TEXTUAL-CONVENTION,RowStatusFROM SNMPv2-TC
InterfaceIndexFROM IF-MIB
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF;atmfCES MODULE-IDENTITYLAST-UPDATED"9611050000Z"ORGANIZATION"ATM Forum Circuit Emulation Working Group"CONTACT-INFO"The ATM Forum
2570 West El Camino Real, Suite 304
Mountain View, CA 94040-1313 USA
Phone: +1 415-949-6700
Fax: +1 415-949-6705
info@atmforum.com"DESCRIPTION"The MIB module used to describe the
Circuit Emulation Interworking Function
(Version 2.0)"REVISION"9502030000Z"DESCRIPTION"The MIB Module to describe the DS1/E1Circuit
Emulation Interworking Function (Version 1.0)
Note: The new Version 2 CES MIB replaces this earlier
Version 1 CES MIB which exists as the (deprecated)
first branch from the overall atmfCESmib object."::={ atmfCESmib 2}atmForum OBJECTIDENTIFIER::={ enterprises 353}atmForumNetworkManagement OBJECTIDENTIFIER::={atmForum 5}atmfCESmib OBJECTIDENTIFIER::={ atmForumNetworkManagement 2}-- An OBJECT IDENTIFIER for all ATM Forum circuit emulation MIBs
-- has been assigned as a branch from the ATM Forum Network
-- Management tree. This MIB for the version 2 ATM Forum Circuit
-- Emulation specification is attached as the second branch from the
-- overall atmfCESmib object.-- The following TEXTUAL-CONVENTIONS are used to link the CES
-- interworking function to ATM interface port, plus the
-- associated VPI and VCI.VpiInteger::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"An integer large enough to hold a VPI"SYNTAXINTEGER(0..4095)VciInteger::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"An integer large enough to hold a VCI"SYNTAXINTEGER(0..65535)CESConnectionPort::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Indicates the port associated with a Circuit Emulation
connection. Objects of this type are always defined as
part of a set that includes
fooPort CESConnectionPort
fooVpi VpiInteger
fooVci VciInteger
The interpretation of these objects is as follows:
1. If no connection exists, 'fooPort' has a value of 0.
Because Interface table entries always have 'ifIndex'
values greater than 0, 'fooPort' reliably serves as a
'connection exists' flag.
If no connection exists, 'fooVpi' and 'fooVci' are
not relevant and have a value of 0.
2. If a PVC or SVC exists, 'fooPort' is defined to have
the value of the MIB-II/RFC1573 'ifIndex' of the ATM
interface associated with the VCC. The ifType
associated with such an ifIndex value is either
atm(37) or atmLogical(80). 'fooVpi' and 'fooVci'
will contain its VPI/VCI."SYNTAXINTEGER(0..2147483647)AtmAddr::=TEXTUAL-CONVENTIONDISPLAY-HINT"1x"STATUScurrentDESCRIPTION"The ATM address used by the network entity. The address
types are: no address (0 octets), E.164 (8 octets), and
NSAP-encoded ATM Endsystem Address (20 octets).
Note: The E.164 address is encoded in BCD format."SYNTAXOCTETSTRING(SIZE(0|8|20))-- This is the MIB module for the ATM Forum Circuit Emulation
-- Service Interoperability Specification Version 2.0.
--
-- This MIB contains four tables:
-- CES Configuration Table
-- CES Mapping Table
-- CES Statistics Table
-- CES Active SVC Table-- CES Configuration TableatmfCESObjects OBJECTIDENTIFIER::={atmfCES 1}atmfCESConfTable OBJECT-TYPESYNTAXSEQUENCEOF AtmfCESConfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The CES configuration table used to manage interworking
between CBR interfaces or channels and ATM Virtual Channel
Links (VCLs). The reverse mapping is shown in the
atmfCESMappingTable."::={ atmfCESObjects 1}atmfCESConfEntry OBJECT-TYPESYNTAX AtmfCESConfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the CES configuration table. There is one
entry in the table per CES entity, mapping one CBR
interface, channel, or bundle to an ATM VCL.
Creation of a row in this table with a non-zero
atmfCESAtmIndex causes a corresponding entry in the
atmVclTable of the ATM-MIB (RFC1695) to be created."INDEX{ atmfCESCbrIndex }::={ atmfCESConfTable 1}
AtmfCESConfEntry ::=SEQUENCE{
atmfCESCbrIndex InterfaceIndex,
atmfCESAtmIndex CESConnectionPort,
atmfCESAtmVpi VpiInteger,
atmfCESAtmVci VciInteger,
atmfCESCbrService INTEGER,
atmfCESCbrClockMode INTEGER,
atmfCESCas INTEGER,
atmfCESPartialFill INTEGER,
atmfCESBufMaxSize INTEGER,
atmfCESCdvRxT INTEGER,
atmfCESCellLossIntegrationPeriod INTEGER,
atmfCESConnType INTEGER,
atmfCESLocalAddr AtmAddr,
atmfCESAdminStatus INTEGER,
atmfCESOperStatus INTEGER,
atmfCESConfRowStatus RowStatus}atmfCESCbrIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The value of this object is equal to MIB II's ifIndex value
of the CBR interface, channel, or bundle that is being
cross-connected to an ATM VCL."::={ atmfCESConfEntry 1}atmfCESAtmIndex OBJECT-TYPESYNTAXCESConnectionPortMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is equal to MIB II's
ifIndex value of the ATM Port interface mapped
through this CES IWF to a CBR interface. This value
is overwritten whenever an active or passive SVC is
established.
The distinguished value zero indicates that no ATM
interface has been specified."::={ atmfCESConfEntry 2}atmfCESAtmVpi OBJECT-TYPESYNTAXVpiIntegerMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is equal to the VPI used
by the ATM VCL mapped through this CES IWF to a CBR
interface. This value is overwritten whenever an
active or passive SVC is established.
The value is not relevant if no ATM interface has been
specified (i.e., atmfCESAtmIndex is set to zero)."::={ atmfCESConfEntry 3}atmfCESAtmVci OBJECT-TYPESYNTAXVciIntegerMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is equal to the VCI used
by the ATM VCL mapped through this CES IWF to a CBR
interface. This value is overwritten whenever an
active or passive SVC is established.
The distinguished value zero indicates that no ATM
VCL has been specified."::={ atmfCESConfEntry 4}atmfCESCbrService OBJECT-TYPESYNTAXINTEGER{unstructured(1),structured(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Define if DSx/Ex service isas structured or unstructurednot. A
structured(2) interface is some nx64kbKbps. An unstructured
(1) interface is 1.544Mbps, 2.048Mbps, 6.312Mbps, 44.736 Mbps,
or 34.368 Mbps. unstructured(1) passes all bits through the
ATM network. strucutured(2) passes data bits through the
ATM network, and may also pass signalling bits
At this time, only unstructured mode is defined for the
44.736 Mbps and 34.368 Mbps services."::={ atmfCESConfEntry 5}atmfCESCbrClockMode OBJECT-TYPESYNTAXINTEGER{
synchronous(1),srts(2),adaptive(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Define if DSx/Ex service clocking mode. This maps into
transmit clock source of CBR interface.
For structured modes this value, if present, must be set to
synchronous(1)."DEFVAL{ synchronous }::={ atmfCESConfEntry 6}atmfCESCas OBJECT-TYPESYNTAXINTEGER{basic(1),e1Cas(2),ds1SfCas(3),ds1EsfCas(4),
j2Cas(5)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This parameter selects which AAL1 Format should be used:
Basic does not carry CAS bits, and uses a single 125 usec frame.
e1Cas, ds1SfCas, dS1EsfCas and j2Cas carry CAS bits in a
multiframe structure for E1, DS1 SF, DS1 ESF and J2
respectively.
This applies to structured interfaces only. Default is
basic (1). For unstructured interfaces this value, if present,
must be set to the default of basic (1)."DEFVAL{ basic }::={ atmfCESConfEntry 7}atmfCESPartialFill OBJECT-TYPESYNTAXINTEGER(0..47)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"If partial cell fill is used, the number of user octets per
cell must be set with this parameter. Setting this parameter
to zero disables partial cell fill, and causes all cells to
be completely filled before they are sent."DEFVAL{0}-- Partial Cell Fill not used::={ atmfCESConfEntry 8}atmfCESBufMaxSize OBJECT-TYPESYNTAXINTEGER(1..65536)UNITS"10 usec"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Define maximum size in 10 microsecond increments of the
reassembly buffer. Some implementations may want allow the
maximum buffer size to be programmed to a size less than the
physical limit to reduce the maximum delay through a circuit."DEFVAL{128}::={ atmfCESConfEntry 9}atmfCESCdvRxT OBJECT-TYPESYNTAXINTEGER(1..65535)
UNITS"10 usec"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The maximum cell arrival jitter in 10 usec increments that
the reassembly process will tolerate in the cell stream
without producing errors on the CBR service interface."DEFVAL{100}::={ atmfCESConfEntry 10}atmfCESCellLossIntegrationPeriod OBJECT-TYPESYNTAXINTEGER(1000..65535)UNITS"msec"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The time in milliseconds for the cell loss integration period.
If a cells are continuously lost for this period of time,
atmfCESCellLossStatus is set to loss (2). The
default definition is 2500."DEFVAL{2500}::={ atmfCESConfEntry 11}atmfCESConnType OBJECT-TYPESYNTAXINTEGER{other(1),pvc(2),activeSvc(3),passiveSvc(4)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The type of ATM connectivity between associated CES IWF's.
Valid values are:
other - none of the types specified below
pvc - supporting connectivity is a permanent
virtual connection
activeSvc - attempt calls whenever none established
passiveSvc - accept calls"::={ atmfCESConfEntry 12}atmfCESLocalAddr OBJECT-TYPESYNTAXAtmAddr
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The ATM address of the local CES IWF process. This address
may be used by the automatic SVC establishment procedures to
identify the intended recipient CES IWF of an incoming automatic
SVC call request. Optionally, the MAX-ACCESS of this object
may be read-only, for those implementations where it is
not desired to manually configure this address."::={ atmfCESConfEntry 13}atmfCESAdminStatus OBJECT-TYPESYNTAXINTEGER{up(1),down(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The desired administrative status of the CES interworking
function. The up and down states indicate that the traffic
flow is enabled or disabled respectively across the CES
interworking function."::={ atmfCESConfEntry 14}
atmfCESOperStatus OBJECT-TYPESYNTAXINTEGER{up(1),down(2),unknown(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The operational status of the CES interworking function.
The up and down states indicate that the traffic flow is
enabled or disabled respectively across the CES interworking
function. The unknown state indicates that the state of the
CES interworking function cannot be determined. The state
will be down or unknown if the supporting CBR or ATM
interfaces are down or unknown, respectively."::={ atmfCESConfEntry 15}atmfCESConfRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-create
STATUScurrentDESCRIPTION"This object is used to create new rows in this table, modify
existing rows, and to delete existing rows."::={ atmfCESConfEntry 16}-- CES Mapping TableatmfCESMappingTable OBJECT-TYPESYNTAXSEQUENCEOF AtmfCESMappingEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The CES mapping table used to show the mapping from ATM
VCLs to CBR interfaces or channels. The mapping and
interworking functions are configured in the
atmfCESConfTable."::={ atmfCESObjects 2}atmfCESMappingEntry OBJECT-TYPESYNTAX AtmfCESMappingEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the CES mapping table. There is one entry
in the table corresponding to each active row in the
atmfCESConfTable for which there is a non-zero
atmfCESAtmIndex."INDEX{ atmfCESAtmIndex,
atmfCESAtmVpi,
atmfCESAtmVci }::={ atmfCESMappingTable 1}
AtmfCESMappingEntry ::=SEQUENCE{
atmfCESMappingCbrIndex InterfaceIndex}atmfCESMappingCbrIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object is equal to MIB II's ifIndex value
of the CBR interface, channel, or bundle that is being
cross-connected to an ATM VCL. Examples of the ifType
value for the CBR entity are ds1(18), ds3(30), ds0(81), or
ds0bundle(82)."::={ atmfCESMappingEntry 1}-- CES Statistics TableatmfCESStatsTable OBJECT-TYPESYNTAXSEQUENCEOF AtmfCESStatsEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"The CES AAL1 statistical data table."::={ atmfCESObjects 3}atmfCESStatsEntry OBJECT-TYPESYNTAX AtmfCESStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the CES AAL1 Stats table. There is one
entry in this table corresponding to each entry in the
atmfCESConfTable."AUGMENTS{ atmfCESConfEntry }::={ atmfCESStatsTable 1}
AtmfCESStatsEntry ::=SEQUENCE{
atmfCESReassCells Counter32,
atmfCESHdrErrors Counter32,
atmfCESPointerReframes Counter32,
atmfCESPointerParityErrors Counter32,
atmfCESAal1SeqErrors Counter32,
atmfCESLostCells Counter32,
atmfCESMisinsertedCells Counter32,
atmfCESBufUnderflows Counter32,
atmfCESBufOverflows Counter32,
atmfCESCellLossStatus INTEGER}atmfCESReassCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This count gives the number of cells played out to the
CES Service Interface. It excludes cells that were
discarded for any reason, including cells that were not used
due to being declared misinserted, or discarded while the
reassembler was waiting to achieve synchronization."::={ atmfCESStatsEntry 1}atmfCESHdrErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of the number of AAL1 header errors detected,
including those corrected. Header errors include correctable
and uncorrectable CRC, plus bad parity."::={ atmfCESStatsEntry 2}atmfCESPointerReframes OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This records the count of the number of events in which the
AAL1 reassembler found that an SDT pointer is not where it is
expected, and the pointer must be reacquired. This count is
only meaningful for structured CES modes, as unstructured CES
modes do not use pointers. For unstructured CES modes, this
count, if present, should indicate zero."::={ atmfCESStatsEntry 3}atmfCESPointerParityErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This records the count of the number of events in which the
AAL1 reassembler detects a parity check failure at the point
where a structured data pointer is expected. This count is only
meaningful for structured CES modes, as unstructured CES modes
do not use pointers. For unstructured CES modes, this count, if
present, should indicate zero."::={ atmfCESStatsEntry 4}atmfCESAal1SeqErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of times that the sequence number of an incoming AAL1
Type 1 SAR-PDU causes a transition from the 'sync' state to
the 'out of sequence' state, as defined by ITU-T I.363.1."::={ atmfCESStatsEntry 5}atmfCESLostCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of lost cells, as detected by the AAL1 sequence number
processing, for example. This records the count of the number
of cells detected as lost in the network prior to the
destination CES IWF AAL1 layer processing."::={ atmfCESStatsEntry 6}
atmfCESMisinsertedCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of AAL1 sequence violations which the AAL Convergence
sublayer interprets as a misinserted cell, as defined by
ITU-T I.363.1."::={ atmfCESStatsEntry 7}atmfCESBufUnderflows OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of buffer underflows. This records the count of the
number of times the CES reassembly buffer underflows. In the
case of a continuous underflow caused by a loss of ATM cell
flow, a single buffer underflow should be counted. If the CES
IWF is implemented with multiple buffers (such as a cell level
buffer and a bit level buffer), then either buffer underflow
will cause this count to be incremented."::={ atmfCESStatsEntry 8}atmfCESBufOverflows OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of buffer overflows. This records the count of the
number of times the CES reassembly buffer overflows. If the CES
IWF is implemented with multiple buffers (such as a cell level
buffer and a bit level buffer, then either buffer overflow will
cause this count to be incremented "::={ atmfCESStatsEntry 9}atmfCESCellLossStatus OBJECT-TYPESYNTAXINTEGER{noLoss(1),loss(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"When cells are continuously lost for the number of milliseconds
specified by atmfCESCellLossIntegrationPeriod, the value is set
to loss (2). When cells are no longer lost, the value is set
to noLoss (1)."::={ atmfCESStatsEntry 10}
-- CES Active SVC TableatmfCESActiveSvcTable OBJECT-TYPESYNTAXSEQUENCEOF AtmfCESActiveSvcEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The table used to manage active SVCs established across ATM
networks between CES entities."::={ atmfCESObjects 4}atmfCESActiveSvcEntry OBJECT-TYPESYNTAX AtmfCESActiveSvcEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the CES active SVC table. There is one
entry in the table corresponding to each active row in
the atmfCESConfTable for which the atmfCESConnType takes
the value 'activeSvc'."INDEX{ atmfCESCbrIndex }::={ atmfCESActiveSvcTable 1}
AtmfCESActiveSvcEntry ::=SEQUENCE{
atmfCESRemoteAddr AtmAddr,
atmfCESFirstRetryInterval INTEGER,
atmfCESRetryTimer INTEGER,
atmfCESRetryLimit INTEGER,
atmfCESRetryFailures Gauge32,
atmfCESActiveSvcRestart INTEGER,
atmfCESActiveSvcOperStatus INTEGER,
atmfCESLastReleaseCause INTEGER,
atmfCESLastReleaseDiagnostics OCTETSTRING}atmfCESRemoteAddr OBJECT-TYPESYNTAXAtmAddrMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The ATM address supporting the corresponding far end
CES IWF process. If no address is supplied, no attempts
to establish the active SVC are initiated."::={ atmfCESActiveSvcEntry 1}atmfCESFirstRetryInterval OBJECT-TYPE
SYNTAXINTEGER(1..3600)UNITS"seconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The time to wait before attempting to establish the SVC
after the first failed call attempt. The time to wait
between subsequent call attempts may differ to implement
a backoff scheme. Zero represents an infinite interval
indicating no retries."DEFVAL{10}::={ atmfCESActiveSvcEntry 2}atmfCESRetryTimer OBJECT-TYPESYNTAXINTEGER(0..86400)UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the current value of the retry timer for
this connection. When the value reaches zero an attempt
will be made to establish the active SVC. When the timer
is not running, the value zero shall be returned."::={ atmfCESActiveSvcEntry 3}atmfCESRetryLimit OBJECT-TYPESYNTAXINTEGER(0..65535)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Sets a maximum limit on how many consecutive unsuccessful
call setup attempts can be made before stopping the attempt
to set up the connection. If this limit is reached then
management action will be required (e.g. setting
atmfCESActiveSvcRestart to 'restart') to initiate a new
attempt to establish the connection. A value of zero
indicates no limit - the attempts will continue until
successful. If this object is not present, no limit on call
attempts is assumed."DEFVAL{0}::={ atmfCESActiveSvcEntry 4}atmfCESRetryFailures OBJECT-TYPE
SYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates how many attempts to establish the connection
have failed. This count is reset whenever a connection
is successfully established or the active SVC is restarted."::={ atmfCESActiveSvcEntry 5}atmfCESActiveSvcRestart OBJECT-TYPESYNTAXINTEGER{restart(1),noop(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"When the value is set to 'restart' the active SVC
is released if necessary and a new setup procedure
is begun. As a result of this action, the
atmfCESActiveSvcOperStatus object transitions to
'establishmentInProgress' (if not already in this state)
and the atmfCESRetryFailures object is cleared.
When the value is set to 'noop' no operation is
performed. When read, the value 'noop' is returned."::={ atmfCESActiveSvcEntry 6}atmfCESActiveSvcOperStatus OBJECT-TYPESYNTAXINTEGER{other(1),establishmentInProgress(2),connected(3),retriesExhausted(4),noAddressSupplied(5),lowerLayerDown(6)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Describes the status of the active SVC. Valid values are:
other - none of the types specified below
establishmentInProgress - connection is not operational,
but call attempts are ongoing
connected - connection is currently operational
retriesExhausted - retry limit has been reached and call
attempts have ceased
noAddressSupplied - no remote address has been configured,
so no call attempts are initiated
lowerLayerDown - underlying CES IWF is not operational
When the row is not 'active', the value of this object is
'other'."::={ atmfCESActiveSvcEntry 7}atmfCESLastReleaseCause OBJECT-TYPESYNTAXINTEGER(1..127)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Value of the Cause field of the Cause information element
in the last RELEASE signalling message received for this
active SVC. Indicates the reason for the release."::={ atmfCESActiveSvcEntry 8}atmfCESLastReleaseDiagnostics OBJECT-TYPESYNTAXOCTETSTRING(SIZE(0..8))
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Value of the first 8 bytes of diagnostic information
from the Cause field of the Cause information element
in the last RELEASE signalling message received for this
active SVC."::={ atmfCESActiveSvcEntry 9}-- Conformance InformationatmfCESConformance OBJECTIDENTIFIER::={ atmfCES 2}atmfCESGroups OBJECTIDENTIFIER::={ atmfCESConformance 1}atmfCESCompliances OBJECTIDENTIFIER::={ atmfCESConformance 2}-- Compliance StatementsatmfCESCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for SNMP entities which support
the ATM Forum Circuit Emulation Services."MODULE-- this moduleMANDATORY-GROUPS{
atmfCESBasicConfigGroup,
atmfCESBasicStatsGroup
}GROUP atmfCESStructConfigGroup
DESCRIPTION"This group is mandatory only for IWFs that
support Structured DS1, E1 or J2 Nx64 kbit/s
Service."GROUP atmfCESStructStatsGroup
DESCRIPTION"This group is mandatory only for IWFs that
support Structured DS1, E1 or J2 Nx64 kbit/s
Service."GROUP atmfCESSvcConfigGroup
DESCRIPTION"This group is mandatory only when support for
automatic SVC initiation procedures is provided."OBJECT atmfCESLocalAddr
MIN-ACCESSread-onlyDESCRIPTION"Support for manual configuration of the local
CES interworking function address is not
required."::={ atmfCESCompliances 1}-- Units of Conformance
atmfCESBasicConfigGroup OBJECT-GROUPOBJECTS{
atmfCESAtmIndex,
atmfCESAtmVpi,
atmfCESAtmVci,
atmfCESCbrService,
atmfCESCbrClockMode,
atmfCESBufMaxSize,
atmfCESCdvRxT,
atmfCESCellLossIntegrationPeriod,
atmfCESConnType,
atmfCESConfRowStatus
}STATUScurrentDESCRIPTION"A collection of objects providing configuration information
for generic Circuit Emulation Service IWFs."::={ atmfCESGroups 1}atmfCESOptionalConfigGroup OBJECT-GROUPOBJECTS{
atmfCESAdminStatus,
atmfCESOperStatus
}STATUScurrentDESCRIPTION"A collection of optional objects providing configuration
information for generic Circuit Emulation Service IWFs."::={ atmfCESGroups 2}
atmfCESBasicStatsGroup OBJECT-GROUPOBJECTS{
atmfCESReassCells,
atmfCESHdrErrors,
atmfCESBufUnderflows,
atmfCESBufOverflows,
atmfCESCellLossStatus
}STATUScurrentDESCRIPTION"A collection of objects providing statistics information
for generic Circuit Emulation Service IWFs."::={ atmfCESGroups 3}atmfCESOptionalStatsGroup OBJECT-GROUPOBJECTS{
atmfCESAal1SeqErrors,
atmfCESLostCells,
atmfCESMisinsertedCells
}STATUScurrentDESCRIPTION"A collection of optional objects providing statistics
information for generic Circuit Emulation Service IWFs."::={ atmfCESGroups 4}atmfCESStructConfigGroup OBJECT-GROUPOBJECTS{
atmfCESCas,
atmfCESPartialFill
}STATUScurrentDESCRIPTION"A collection of objects providing configuration information
for Structured DS1, E1 or J2 Nx64 kbit/s Service IWFs."::={ atmfCESGroups 5}atmfCESStructStatsGroup OBJECT-GROUPOBJECTS{
atmfCESPointerReframes
}STATUScurrentDESCRIPTION"A collection of objects providing statistics information
for Structured DS1, E1 or J2 Nx64 kbit/s Service IWFs."::={ atmfCESGroups 6}atmfCESOptionalStructStatsGroup OBJECT-GROUPOBJECTS{
atmfCESPointerParityErrors
}STATUScurrentDESCRIPTION"A collection of optional objects providing statistics
information for Structured DS1, E1 or J2 Nx64 kbit/s Service
IWFs."::={ atmfCESGroups 7}
atmfCESMappingGroup OBJECT-GROUPOBJECTS{
atmfCESMappingCbrIndex
}STATUScurrentDESCRIPTION"A collection of objects providing information about the
mapping from ATM VCLs to CBR interfaces or channels."::={ atmfCESGroups 8}atmfCESSvcConfigGroup OBJECT-GROUPOBJECTS{
atmfCESLocalAddr,
atmfCESRemoteAddr,
atmfCESFirstRetryInterval,
atmfCESRetryTimer,
atmfCESRetryFailures,
atmfCESActiveSvcRestart,
atmfCESActiveSvcOperStatus
}STATUScurrentDESCRIPTION"A collection of objects providing SVC connection
establishment support configuration information for CES
IWFs."::={ atmfCESGroups 9}atmfCESOptionalSvcConfigGroup OBJECT-GROUP
OBJECTS{
atmfCESRetryLimit,
atmfCESLastReleaseCause,
atmfCESLastReleaseDiagnostics
}STATUScurrentDESCRIPTION"A collection of optional objects providing SVC connection
establishment support configuration information for CES
IWFs."::={ atmfCESGroups 10}END